A105N Lap Joint Flange FF CL600 4 Inch

Quick Details

• Size: 4" (DN100)

• Material: Carbon steel A105N

• Place of Origin: Zhejiang, China (Mainland)

• Brand Name: Tanell

• Standard or Nonstandard: Standard

• Technics: Forged

• Standard: AST, ANSI, etc

• Type: A105N Lap Joint Flange

Packaging & Delivery

Packaging Details:	Seaworthy plywood case or as customer requests
Delivery Detail:	2 - 10 days after receiving the deposit

Specifications

A105N Lap Joint Flange FF
1. Material: Carbon steel A105N

2. Size: 4" (DN100)

3. Standard: ASTM B16.5, DIN, etc

4. Pressure: 600#, etc

A105N Lap Joint Flanges are used for ambient and high temperature services and by nature have hardness level and nickel content within the limit of NACE. ASTM A105 has no grade.

Sometimes A105N is described. N stands not for Grade, but for normalized. Normalizing is a type of heat treatment, applicable to ferrous metals only. The purpose of normalizing is to remove the internal stresses induced by heat treating, casting, forming etc. A105 / A105N lap jointflanges are used in low and middle pressure fluid pipe line, boiler, petroleum and natural gas industry, electric industry , shipbuilding, fertilizer equipment, etc...

Chemical Composition Of A105N Carbon Steel

Mechanical Requirement

Type	A105N Lap Joint Flange
Size	4" (DN100)
Standards	SO, WN, SW, TH, LJ, BL, PL, etc
Material	Carbon Steel: ASTM: A105N/A105, ASTM SA350 LF2,etc Stainless Steel: ASTM A182 F304/304L/316/316L, etc Alloy Steel: ASTM A182 F1/F5/F9/F11/F22/F91, Etc. Duplex stainless steel: ASTM A182 F51, etc Super Duplex Stainless Steel: S32750/2507/F53/F55, UNS32760, etc Nicke alloys: Nickel 200, Monel 400, Inconel 600/625, Incoloy 825/800,                     Hastelloy C276, Hastelloy C276, Hastelloy B1/B2/B3, Alloy 20, etc Cu-Ni: 90/10,70/30, etc
Applications	Petroleum,chemical,power,gas,metallurgy, shipbuilding, construction, etc

About: A105N Lap Joint Flange

A105N Lap Joint Flange (LJ Flanges) or A105N Loose flange (A105N LF flange) called are used on piping fitted with lapped pipe or with lap joint stub ends the combined initial cost of the two items being approximately one-third higher than that of comparable welding neck flanges. Their pressure-holding ability is little, if any, better than that of slip-on flanges and the fatigue life of the assembly is only one-tenth that of welding neck flanges. The A105N lap joint flanges with the stub end assembly are normally used in systems requiring frequent dismantling for inspection and cleaning and where the ability to swivel flanges and to align bolt holes materially eases the erection of large diameter or unusually stiff piping. A105N Lap Joint flanges have certain special advantages: Freedom to swivel around the pipe facilitates the lining up of opposing flange bolt holes. Lack of contact with the fluid in the pipe often permits the use of inexpensive carbon steel flanges with corrosion resistant pipe. In systems which erode or corrode quickly, the flanges may be salvaged for re-use.

Slip on flanges with a hub have published specifications that range from 1/2" thru 24".  Sizes above 24" are produced as lap joints to slip on dimensions.  Tanell provides A105N Lap Joint flanges in all material grades, specifications and sizes.

Tanell manufactures lap joint flanges in all steel material grades, including Super duplex stainless steel lap joint flanges, stainless steel lap joint flanges and alloy lap joint flanges.  Tanellg also has many different lap joint flanges in stock and ready to ship.  Tanell can also manufacture custom pipe flanges according to customer specifications.

Materials For Lap Joint Flange

The most common materials used in flanges produced is carbon steel, super duplex stainless steel, duplex stainless steel, stainless steel, cast iron, aluminium, brass, bronze, plastic etc.

In addition, flanges, like fittings and pipes, for specific purposes sometimes internally equipped with layers of materials of a completely different quality as the flanges themselves, which are "lined flanges".

The material of a flange, is basically set during the choice of the pipe, in most cases, a flange is of the same material as the pipe.

Installation of A105N Lap Joint Flange

Center the gasket on the flange. This is extremely vital where raised faces are involved. Note: standard ANSI ring gaskets, when cut properly, should center themselves with the bolts in place.

Use a torque wrench and well-lubricated fasteners with hardened flat washers to ensure correct initial loading.

Tighten bolts to compress gasket uniformly. This means going from side to side around the joint, in a star-like crossing pattern.

All bolts should be tightened in one-third increments, according to proper bolting patterns. Retorque 12 to 24 hours after start-up, whenever possible.

All applicable safety standards including lockout/tagout procedure should be observed.

Never use liquid or metallic based anti-stick or lubricating compounds on the gaskets. Premature failure could occur as a result.

APPLICATIONS Of A05N Lap Joint Flange:                          

1. petrochemical industry

2. Pharmaceutical industry

3. Food industry

4. Aviation and aerospace industry

5. Architectural decoration industry

6. Oil and gas industry

Other Features:

1) Chemical and Physical characteristic: durable, corrosion resistant and high-temperature resistant

2) We also produce flange with special specifications according to customers’ requirements;

Packing

1) Packing Method:

Normal packing: Plastic film or bubble paper wrapped, endings protect by caps,

then into wooden case or load on fumigation plywood pallet.

Custom product: As per your request.

2) Shipping:

By Sea, By Air, By Train or River-and-Sea Coordinated Transport, according to your request.

Where can we find the high quality A105N Lap Joint Flange FF 600# 4 Inch